AFFILIATE DISCLOSURESpecForgePC is reader-supported. As an Amazon Associate, we earn from qualifying purchases. Learn more →
RAM & SSD UpgradesUpdated 2026-10-21 · 7 min read

Lenovo Legion 5i 16 (Gen 9) RAM & SSD Upgrade Guide: Dual SO-DIMM & M.2 Slots

A hardware upgrade walkthrough for the Lenovo Legion 5i 16IRX9. We cover dual DDR5-5600 SO-DIMM memory installation, secondary M.2 2280 SSD slot clearance, and thermal shield reassembly.

SF
SpecForgePC Documentation TeamManufacturer-Documented Hardware Analysis

As an Amazon Associate, we earn from qualifying purchases.

Quick Answer

The Lenovo Legion 5i 16IRX9 (Type 83DG) provides complete internal upgradeability for both memory and storage. Unlike thinner ultrabooks with soldered silicon, the motherboard features two standard DDR5 SO-DIMM slots supporting up to 64GB (2x 32GB) DDR5-5600 RAM, and two full-length M.2 2280 PCIe 4.0 x4 NVMe SSD slots. Slot 2 is unoccupied from the factory and includes a pre-installed aluminum heat spreader, allowing direct storage expansion without cloning or replacing the factory operating system drive.

Key Hardware Takeaways

  • Modular Memory Architecture: Two standard 262-pin DDR5 SO-DIMM slots allow memory upgrades from factory 16GB up to 64GB DDR5-5600 at 1.1V.
  • Dual M.2 2280 Slots: Both storage slots support full-speed PCIe 4.0 x4 NVMe drives; Slot 2 is completely free for secondary drives up to 4TB.
  • Factory Thermal Shields: Both M.2 slots feature stamped aluminum cooling plates with pre-applied thermal pads to dissipate heat into the lower chassis.
  • Disassembly Requirements: Accessing the motherboard requires removing 10 Phillips #0 screws and releasing perimeter retention clips using a plastic pry tool.

Internal Motherboard Layout & Component Locations

The Lenovo Legion 5i 16IRX9 (Type 83DG) features one of the most serviceable gaming laptop motherboards in its class. When the bottom plate is removed, the internal layout is organized into clean functional zones:

  • Central Memory Enclosure: Located directly between the twin cooling fans beneath an EMI/thermal shield. Inside are two horizontal 262-pin DDR5 SO-DIMM slots.
  • Primary M.2 NVMe Slot (Right Side): Houses the factory operating system drive beneath a dedicated stamped aluminum heat shield.
  • Secondary M.2 NVMe Slot (Left Side): Empty from the factory. Accommodates a full-length M.2 2280 PCIe 4.0 x4 solid-state drive up to 4TB.
  • 80Wh Integrated Battery: Occupies the lower front section, secured by Phillips screws with a centralized motherboard power harness.

DDR5 SO-DIMM Specifications & Speed Constraints

Memory compatibility on Intel 14th Gen HX platforms requires close attention to JEDEC voltage standards and module height:

  • Form Factor: Standard 262-pin DDR5 Small Outline Dual In-Line Memory Module (SO-DIMM). Desktop DIMMs are incompatible.
  • Speed & Timings: Official PSREF rating is DDR5-5600 (PC5-44800). The Intel Core i7-14650HX memory controller operates these modules at 1.1V JEDEC baseline timings (CL46).
  • Maximum Capacity: While Lenovo validates 32GB (2x 16GB) in factory SKUs, the motherboard chipset and UEFI BIOS fully support 64GB (2x 32GB) dual-channel configurations.
  • XMP Limitations: HX gaming laptops generally lack manual BIOS timing adjustments; always select standard JEDEC-profile modules like the Crucial Pro DDR5 kit rather than aggressive desktop-voltage kits.

Secondary M.2 2280 NVMe SSD Installation Rules

Expanding storage on the Legion 5i 16IRX9 is remarkably straightforward because Slot 2 operates on its own dedicated PCIe 4.0 x4 bus lanes linked directly to the Intel HM770 chipset:

  • Form Factor Compatibility: Both slots accept standard M.2 2280 (22mm x 80mm) drives. Slot 2 also includes a pre-tapped standoff hole for smaller M.2 2242 drives if using an OEM carrier.
  • Thickness & Heatsink Clearance: The factory aluminum thermal plate sits flush against the SSD using a 0.5mm silicone thermal pad. You must purchase a bare, single-sided SSD like the Samsung 990 Pro. Do not purchase drives with pre-installed thick finned aluminum heatsinks, as the chassis bottom cover will not close.
  • Thermal Dissipation: Ensure the blue protective plastic film on the pre-installed thermal pad is peeled off before reinstalling the metal cover over the new drive.

Step-by-Step Chassis Disassembly Procedure

  1. Disable the Battery in BIOS: Power on the laptop and immediately tap F2 to enter Lenovo UEFI BIOS Setup. Navigate to Configuration > Disable Building-in Battery and press Enter. Confirm with Yes. The laptop will immediately shut down, safely isolating motherboard power rails.
  2. Remove Bottom Screws: Place the machine upside down on a non-scratch anti-static mat. Using a precision Phillips #0 screwdriver, extract the 10 bottom cover screws. Keep note that the 4 screws along the front edge are shorter (M2 x 4mm) than the 6 rear screws (M2 x 12mm).
  3. Release Edge Retention Clips: Insert a thin plastic pry tool into the seam along the side vents. Gently slide around the perimeter toward the rear exhaust to disengage the internal plastic clips. Never use metal screwdrivers to pry the casing.
  4. Access Memory Slots: Pry off the central rectangular aluminum EMI shield using a plastic spudger. Release the SO-DIMM side clips to eject existing modules, and slide in replacement DDR5 modules at a 30-degree angle until they click into horizontal retention arms. Snap the EMI shield back in place.
  5. Install Secondary NVMe SSD: Locate Slot 2 on the left side of the battery. Remove the single Phillips screw securing the metal thermal shield. Slide your new M.2 2280 drive into the connector, peel the protective liner from the thermal pad, lay the shield over the drive, and re-tighten the mounting screw.
  6. Reassemble & Reconnect Power: Press the bottom cover back onto the chassis until all perimeter clips audibly snap into place. Reinstall the 10 screws in their original positions. Connect the factory 230W AC adapter to deactivate maintenance shipping mode and boot Windows.

BIOS Hardware Recognition & Windows Storage Setup

After upgrading your components, verify system health:

  • RAM Verification: Boot into Windows and open Task Manager (Ctrl + Shift + Esc). Under the Performance > Memory tab, confirm that the system displays 32GB or 64GB running at 5600 MT/s in dual-channel mode.
  • SSD Initialization: Right-click the Windows Start icon and open Disk Management. An "Initialize Disk" dialog will appear for the secondary drive. Select GPT (GUID Partition Table), right-click the unallocated partition, select New Simple Volume, and format as NTFS.

Where to buy: check the current price and configuration of the Lenovo Legion 5i 16 (i7-14650HX, RTX 4070) on Amazon (full specs), Samsung 990 PRO 2TB NVMe M.2 SSD (7,450 MB/s) on Amazon (full specs), Crucial Pro 32GB Kit (2x16GB) DDR5-5600 RAM on Amazon (full specs).

Frequently Asked Questions

Does opening the chassis to upgrade RAM or SSD void the Lenovo warranty?

No. In the United States, user-serviceable components like SO-DIMM memory and M.2 storage can be upgraded without voiding the manufacturer warranty under the Magnuson-Moss Warranty Act, provided no physical damage is caused during the procedure.

Can I install 64GB of RAM in the Legion 5i 16IRX9?

Yes. Although Lenovo PSREF documentation lists 32GB as the maximum factory offering, the Intel HM770 chipset and Core i7-14650HX memory controller fully recognize and stabilize 64GB (2x 32GB) DDR5-5600 SO-DIMM configurations.

Does the secondary M.2 slot support PCIe 5.0 NVMe drives?

No. Both M.2 slots on the Legion 5i 16IRX9 operate on PCIe 4.0 x4 electrical lanes. While a PCIe 5.0 drive will physically fit and operate via backwards compatibility, transfer speeds will be capped at PCIe 4.0 bandwidth (approx 7,450 MB/s).

Do I need an SSD with a built-in heatsink?

No. Do not buy an SSD with a thick pre-attached heatsink. Lenovo includes custom stamped metal heat spreaders with thermal pads in both slots that screw directly into the chassis standoffs.

Documented Primary Sources

This guide is based on the following documentation: